Hear from Our Customers
Kitec doesn’t give you much warning. One day everything’s fine. The next, you’re dealing with a burst pipe and water spreading through your walls.
That’s the reality with these systems. The brass fittings corrode from the inside. The pipes delaminate. And when they go, they go fast.
A complete Kitec pipe repair in Sheridan, CA means replacing the entire system with materials that won’t fail in ten years. Copper or PEX. Proper fittings. Work that’s done right so you can stop worrying about when the next leak will hit. You’ll sleep better knowing your home is protected, your property value is intact, and you won’t be scrambling to find an emergency plumber at 2 AM because a pipe let go.
Most homeowners don’t realize how much damage can happen in just a few hours. Water gets into drywall, insulation, flooring. The repair bill climbs fast. Replacing Kitec before it fails isn’t just smart—it’s cheaper than dealing with the aftermath.
We’ve been handling plumbing emergencies and full system replacements for over a century. We know Sheridan homes. We know the water conditions here. We know what fails and why.
When you call, you’re getting licensed plumbers who’ve seen hundreds of Kitec systems and know exactly what needs to happen. We show up on time, assess the situation honestly, and give you a price that won’t change halfway through the job.
We’re available 24/7 because Kitec doesn’t wait for business hours. Our trucks are stocked. Our team is ready. And we’ve built our reputation in Sheridan, CA on doing what we say we’ll do—fast, fair, and done right the first time.
You call. We answer. If it’s an emergency, we’re there fast to stop the leak and prevent further damage.
Once things are stable, we inspect your entire system. Kitec isn’t a “fix one spot and hope for the best” situation. If one section failed, others are likely close behind. We’ll show you what’s happening, explain what needs replacing, and give you an upfront price for the complete job.
The replacement process involves removing all Kitec pipes and fittings, then installing new copper or PEX throughout your home. We work efficiently to minimize disruption. Most homes take a few days depending on size and access. We handle wall and ceiling access carefully, and we coordinate any drywall work that’s needed after.
When we’re done, you’ll have a plumbing system that’s built to last decades, not years. We test everything, walk you through what we did, and make sure you understand your new system. No diagnostic fees. No surprise charges. Just the price we quoted.
Ready to get started?
A full Kitec plumbing services job in Sheridan, CA covers every pipe and fitting in your system. Hot water lines. Cold water lines. Connections to your water heater, fixtures, and appliances. We don’t leave any Kitec behind because leaving it means leaving the problem.
Sheridan homes built or renovated between 1995 and 2007 are the most likely to have Kitec installed. If you see blue and orange pipes with ASTM 1281 labels, that’s Kitec. Even if it hasn’t leaked yet, the clock is ticking. Water temperatures above 180°F and high water pressure accelerate the corrosion process, and both are common in this area.
We replace everything with high-grade materials—typically copper or PEX depending on your home’s layout and your preference. Both are proven, reliable, and won’t suffer from the same dezincification issues that plague Kitec brass fittings. The work includes proper permits, code-compliant installation, and a system that will actually hold up.
If your Kitec system has already caused water damage, we can help you document everything for insurance claims. We’ve worked with plenty of homeowners through that process and know what insurance companies need to see.
A complete Kitec replacement typically runs between $8,000 and $15,000 for most homes in Sheridan, CA. The range depends on your home’s size, how accessible your plumbing is, and whether we need to open walls or ceilings to reach everything.
Partial repairs—fixing just one leak—might seem cheaper upfront, but they don’t solve the underlying problem. Kitec systems fail systematically, not randomly. Fixing one spot means you’re likely looking at another failure within months. Multiple emergency repairs add up fast, often costing more than a complete replacement would have.
We give you an exact price before we start any work. No diagnostic fees. No hourly rates that climb as the job goes on. The number we quote is the number you pay, and in many cases, our final cost comes in lower than the estimate because we work efficiently and don’t pad the bill.
You can, but it’s not a solution—it’s a delay. Kitec fails because of how it’s made, not because of one bad section. The brass fittings corrode. The pipe layers separate. These problems exist throughout your entire system, not just where the leak showed up.
Repairing one leak buys you a few months, maybe a year if you’re lucky. Then another section fails. Then another. Each time, you’re paying for an emergency call, repairs, and possibly water damage cleanup. It’s expensive, stressful, and inevitable.
The only permanent fix for Kitec plumbing problems in Sheridan, CA is complete replacement. Remove all of it. Install materials that won’t fail the same way. That’s not a sales pitch—it’s what every plumbing expert will tell you because it’s the only approach that actually works long-term.
Most homes take two to four days for a complete Kitec pipe repair in Sheridan, CA. Smaller homes or condos might be faster. Larger homes with multiple bathrooms and complex layouts might take a bit longer.
The timeline depends on how much plumbing you have and how easy it is to access. If your pipes run through finished walls and ceilings, we’ll need to create access points, which adds time. If you have a crawl space or unfinished basement, the work goes faster.
We work efficiently and keep disruption to a minimum. You’ll have water shut off during active work hours, but we make sure you have working toilets and water access at the end of each day. We coordinate with you on timing so the project fits your schedule as much as possible. Once the plumbing work is done, any drywall patching or painting is separate, but we can recommend trusted contractors if you need them.
Insurance usually covers water damage caused by Kitec leaks, but not the cost of replacing the Kitec system itself. That’s considered a maintenance issue or pre-existing condition, which most policies exclude.
If your Kitec has already leaked and caused damage, document everything. Take photos. Keep receipts. Get a detailed report from us showing what failed and what damage resulted. Insurance companies need that documentation to process claims, and we’ve helped plenty of Sheridan homeowners put together what they need.
The class action lawsuit against Kitec manufacturers ended years ago, and the deadline to file claims has passed. That means replacement costs fall on homeowners now. Some people have had luck negotiating with insurance companies, especially if the leak caused significant damage, but it’s not guaranteed. What is guaranteed is that replacing Kitec before it fails is far less expensive than dealing with a catastrophic leak and the water damage that follows.
Look for blue and orange pipes, usually with ASTM 1281 printed on them. Blue indicates cold water lines. Orange indicates hot water lines. You’ll typically see these in your water heater area, under sinks, or in unfinished spaces like basements or crawl spaces.
Kitec was installed primarily between 1995 and 2007, so if your Sheridan home was built or had plumbing work done during that window, there’s a good chance you have it. The system was marketed as a cost-effective alternative to copper, and many builders used it widely before the recall.
If you’re not sure, we can inspect your plumbing and tell you definitively what you have. That inspection is free—no charge, no obligation. We’d rather you know what’s in your walls than be surprised by a burst pipe later. Even if you’re not ready to replace the system immediately, knowing what you have helps you plan and budget for the work before an emergency forces your hand.
Both copper and PEX are solid choices for replacing Kitec, and both will last decades longer than what you have now. Copper is the traditional option—proven, durable, and familiar to most homeowners. It handles high temperatures well and doesn’t degrade over time.
PEX is newer but widely accepted and code-compliant. It’s flexible, which makes installation faster in tight spaces and reduces the number of fittings needed. Fewer fittings mean fewer potential leak points. PEX also costs less than copper in most cases, which can bring your total replacement cost down.
The choice often comes down to your home’s layout and your personal preference. If your plumbing runs through tight spaces or has lots of turns, PEX makes sense. If you prefer the look and feel of copper, or if your home’s existing setup works better with rigid pipe, copper is the way to go. We’ll walk you through both options during your consultation and recommend what makes the most sense for your specific situation in Sheridan, CA.
Local Resources
Other Services we provide in Sheridan
