Hear from Our Customers
You stop wondering when the pipes will burst. That’s the first thing you get—actual sleep at night instead of listening for dripping sounds in your walls.
Your insurance company stops flagging your policy. Kitec plumbing problems aren’t just inconvenient—they’re a known defect that makes insurers nervous. Some won’t cover water damage from Kitec at all. Others jack up your premiums or drop you entirely when they find out it’s still in your walls.
Complete Kitec pipe repair in Rosemont means modern materials that won’t corrode from the inside out. You’re not patching one leak just to watch another section fail six months later. The whole system gets replaced—supply lines, fittings, connections—so you’re done dealing with this for good.
And if you’re thinking about selling? Buyers run when they see Kitec. It tanks your home value and scares off anyone who knows what they’re looking at. Replacing it now means you can actually list your property without that liability hanging over every negotiation.
We’ve spent over two decades handling residential and commercial plumbing throughout El Dorado County and Sacramento County. We’re licensed, insured, and we’ve seen what Kitec does to homes when it finally lets go.
Rosemont properties built between 1995 and 2007 are the most likely to have Kitec installed. If you’re in that window and haven’t checked, you should. We’ll come out, assess what you’re dealing with, and give you an exact cost before we start any work. No surprises, no upselling—just the real numbers so you can make an informed decision.
Our reputation here comes from showing up on time, doing what we said we’d do, and charging what we quoted. That’s it. We’re not the cheapest option in town, but we’re the one that gets it right the first time so you’re not calling someone else to fix our work.
First, we come out and confirm you actually have Kitec. It’s usually marked with “Kitec” or “KTC” on the pipes, often orange or blue. We’ll trace your supply lines, check your water heater connections, and figure out how much of your system needs replacing.
Then we give you a written estimate. You’ll know the full cost, the timeline, and what materials we’re using—typically PEX or copper, depending on your home’s layout and your budget. We pull the necessary permits because this isn’t patch work, it’s a complete replacement that needs to be done to code.
During the job, we shut off your water, remove all the Kitec piping and brass fittings, and install the new system. Depending on your home’s size and how accessible the pipes are, this usually takes one to three days. We test everything before we leave—pressure, connections, flow—so you know it’s solid.
You get a clean workspace when we’re done. We’re not leaving drywall dust everywhere or half-finished walls. The job gets completed, inspected, and you move on with a plumbing system that actually works.
Ready to get started?
You’re getting a full system overhaul. That means removing every section of Kitec pipe—not just the parts that are leaking now, but all of it. The brass fittings come out too, since they corrode just as badly as the pipes themselves.
We replace your supply lines with either cross-linked polyethylene (PEX) or copper, depending on what makes sense for your home. PEX is flexible, cost-effective, and holds up well in Rosemont’s water conditions. Copper costs more upfront but some homeowners prefer it for resale value or personal preference. We’ll walk you through both options so you understand what you’re paying for.
The work includes new shut-off valves, updated connections to your water heater, and any necessary drywall or access panel repairs. We’re not just swapping pipes and leaving you with holes in your walls. Everything gets put back together so it looks like we were never there—except for the part where your plumbing actually works.
In Rosemont, most homes we work on fall in the $6,500 to $12,000 range for complete Kitec replacement, depending on square footage and how the original plumbing was routed. That’s a fraction of what you’d pay for water damage restoration if a pipe bursts while you’re at work or on vacation. And it’s a one-time fix, not an ongoing cycle of emergency repairs every time another section fails.
Check your water heater connections, under sinks, and anywhere you can see exposed pipes. Kitec is usually blue or orange, though sometimes it’s gray. The pipes themselves are often stamped with “Kitec,” “KTC,” or “XPA.”
If your home was built or renovated between 1995 and 2007, there’s a decent chance Kitec was used. It was popular with builders because it was cheap and easy to install. Nobody knew it would fail this badly until years later when the lawsuits started piling up.
You can also look at your brass fittings. If they’re dezincified—meaning they look crusty, white, or powdery—that’s a red flag. Kitec’s brass fittings are just as problematic as the pipes. They break down from the inside, weaken, and eventually crack under normal water pressure.
You can, but you’re buying yourself maybe six months before another section goes. Kitec doesn’t fail in one spot and then behave—it fails systemically because the entire system is degrading at the same rate.
The pipes corrode from the inside due to a reaction between the aluminum layer and your water supply. That process is happening throughout your whole system, not just where you see the leak today. Patching one area doesn’t stop the corrosion in the rest of your walls.
Most homeowners who try the repair route end up spending more in the long run. You’re paying for multiple service calls, water damage cleanup, and the stress of never knowing when the next leak will hit. Complete replacement costs more upfront, but it’s the only way to actually solve the problem instead of managing it indefinitely.
Most single-family homes take one to three days, depending on size and how your plumbing was originally installed. A straightforward ranch with accessible crawl space? We can usually finish in a day or two. A two-story home with pipes running through finished walls? That’s closer to three days.
We’re not tearing apart your entire house. We make strategic access points where we need them, run the new lines, and close everything back up. If your pipes are in the attic or crawl space, the work goes faster. If they’re buried in walls or concrete slab, it takes longer because we have to be more careful about access and restoration.
You’ll have water shut off during active work hours, but we’ll get you back up and running each evening if the job spans multiple days. We’re not leaving you without water overnight unless there’s a specific reason we can’t restore temporary service.
Probably not. Most insurance policies don’t cover the cost of replacing defective materials—they only cover sudden, accidental damage that results from a failure. So if your Kitec bursts and floods your house, they might cover the water damage restoration, but they won’t pay to replace the plumbing system itself.
And that’s if they cover the water damage at all. Some insurers specifically exclude Kitec-related claims because it’s a known defect with a 100% failure rate. They consider it a maintenance issue, not an accident, since everyone knows Kitec eventually fails.
There was a class action settlement a few years back that paid out to homeowners who had Kitec, but the deadline to file a claim passed in January 2020. If you’re dealing with this now, you’re covering the replacement cost yourself. The good news is that once it’s done, you won’t have insurance companies threatening to drop your coverage or spike your premiums because of it.
You’re looking at serious water damage—potentially tens of thousands of dollars depending on where the pipe fails and how long the water runs before you catch it. Kitec doesn’t just drip when it goes. The pipes and fittings burst under normal water pressure, sending a full flow of water into your walls, ceilings, or floors.
If it happens while you’re home, you might catch it fast enough to minimize damage. Shut off your main water line immediately and start moving anything valuable away from the water. Then call us for emergency Kitec leak repair in Rosemont—we respond quickly because we know these situations don’t wait.
If it happens while you’re at work or on vacation, you’re coming home to a disaster. Water will run for hours, soaking insulation, drywall, flooring, and anything else in its path. You’ll need water extraction, mold remediation, and full restoration on top of the plumbing repair. That’s why replacing Kitec before it fails isn’t just smart—it’s the only move that makes financial sense.
For most homes, you’re looking at $6,500 to $12,000 for complete replacement. Smaller homes with simple layouts land on the lower end. Larger homes with multiple bathrooms, complex routing, or pipes buried in concrete cost more.
The price includes removing all the old Kitec piping and fittings, installing new PEX or copper lines, updating shut-off valves, reconnecting your water heater and fixtures, and repairing any drywall or access points we had to create. We give you the exact number upfront after we assess your specific situation—no ballpark ranges that magically double once we start working.
Compare that to water damage restoration, which averages $2,500 to $7,500 for a single incident—and that’s assuming you catch it early. A major burst pipe can easily hit $20,000 or more in repairs. Replacing your Kitec plumbing problems now costs less than one bad failure, and it eliminates the risk of it happening again. That’s not a sales pitch. That’s just math.
Local Resources
Other Services we provide in Rosemont
