Hear from Our Customers
If your home was built between 1995 and 2007 in Cold Springs, there’s a real chance you have Kitec plumbing. Those bright orange and blue pipes seemed fine when they went in. But Kitec has a universal defect—the brass fittings corrode from the inside out, and the pipes themselves degrade over time.
It’s not a question of if they’ll fail. It’s when. And when they do, you’re looking at flooded rooms, damaged drywall, ruined floors, and repair bills that make a full repipe look cheap by comparison.
A Kitec repipe in Cold Springs, CA means you replace the problem before it replaces your peace of mind. You get consistent water pressure again. No more chalky buildup. No more wondering if today’s the day a fitting gives out while you’re at work. Just reliable plumbing that does its job quietly for the next 50 to 75 years.
You stay in your home during the work. Most residential Kitec repiping services in Cold Springs take just a few days. And once it’s done, you’re free from that low-grade anxiety every time you hear water running through the walls.
We’ve served Cold Springs and the surrounding El Dorado County area since the late ’90s. We’ve seen Kitec go in, watched it start failing right on schedule around 2005, and we’ve been pulling it out ever since.
We’re a licensed contractor (CA License #916322), fully insured, and we don’t play games with pricing. You get a clear estimate before we touch anything, and the final number doesn’t magically grow once we’re halfway through the job.
Cold Springs sits in the heart of an area where Kitec was installed heavily during the building boom. We know the housing stock here. We know what’s behind your walls. And we know how to get you repiped fast without tearing your house apart in the process.
First, we walk through your property and map out where the Kitec runs. We identify access points, plan the new routing, and give you an upfront cost that includes materials, labor, and any drywall patching or paint touch-ups.
Once you approve, we start pulling out the old Kitec and installing either PEX or Type L copper—your choice. PEX is flexible, fast to install, and lasts up to 75 years. Copper costs a bit more but some people just prefer it. Both are light-years better than what you have now.
We work in sections so your water’s only off for short periods. You can still use your kitchen and bathrooms while we’re working in other parts of the house. Most residential and commercial Kitec repiping jobs in Cold Springs wrap up in three to five days depending on square footage and complexity.
After the new pipes are in and tested, we close up the walls, patch, and paint to match. You’re left with a clean finish and a plumbing system you won’t have to think about again for decades.
Ready to get started?
A complete Kitec repipe in Cold Springs, CA means we replace every inch of Kitec in your home—hot and cold lines, from the water heater to every fixture. You’re not patching a leak and hoping the rest holds. You’re eliminating the entire problem.
We install new shut-off valves, pressure-test the system, and make sure everything’s up to current California plumbing code. That matters if you ever sell. Buyers and inspectors in El Dorado County know what Kitec is, and they know it’s a liability. A documented repipe removes that obstacle and keeps your home marketable.
You also get better water quality. Kitec pipes leach contaminants as they break down, and that chalky buildup you see at faucets? That’s in your water too. New pipes mean cleaner water and better pressure throughout the house.
And here’s the thing nobody talks about—insurance. A lot of carriers in California won’t cover water damage from Kitec failures anymore, or they’ll drop you after one claim. A professional Kitec repiping in Cold Springs protects you from being stuck with a five-figure repair bill and no coverage.
Check your water heater, under sinks, and in any exposed areas like a basement or crawl space. Kitec pipes are usually bright orange for hot water lines and blue for cold water lines. They’re plastic (PEX) with brass fittings at the connections.
Look for stamps on the pipe itself that say “Kitec,” “KTC,” or “IPEX KITEC.” The fittings are the real giveaway—they’re brass-colored and often have a specific oval shape. If your home in Cold Springs was built or repiped between 1995 and 2007, and you see those orange and blue pipes, it’s Kitec.
If you’re not sure, call us. We can identify it in about five minutes, and there’s no charge for that. It’s worth knowing, because waiting on a Kitec replacement isn’t a good strategy. These pipes have a failure rate high enough that it’s a matter of when, not if.
For most homes in Cold Springs, you’re looking at somewhere between $5,000 and $15,000 for a complete repipe with PEX. Copper runs higher—usually $6,000 to $20,000 depending on the size of your home and how accessible the plumbing is.
A 1,200 square foot house with two bathrooms is going to cost less than a 2,500 square foot place with three bathrooms and a laundry room on the second floor. If we have to open up more walls or deal with a complex layout, that adds time and materials.
We give you an exact number before we start. No surprises, no “we found something” upcharges halfway through. And honestly, when you compare that cost to what happens when Kitec fails—water damage, mold remediation, lost belongings, temporary housing—it’s not even close. The repipe is cheaper, and you’re in control of the timing.
Most residential Kitec repipe jobs in Cold Springs take three to five days. Smaller homes or condos might be done in two. Larger properties with multiple stories or complicated layouts can take a week.
You stay in your home the whole time. We work in sections, so your water’s only off for short stretches while we’re connecting the new lines. You can still use your kitchen and bathrooms—we coordinate with you so it’s not a huge disruption.
The timeline depends on square footage, how many fixtures you have, and how easy it is to access the existing pipes. If everything’s open in a crawl space or attic, it goes faster. If we’re working through finished walls, it takes a bit longer. Either way, we move fast and clean up as we go.
Both are solid choices, and both will outlast you. PEX is flexible, faster to install, and costs less. It’s rated for up to 75 years, handles temperature changes well, and it’s what most people choose for residential Kitec repiping services in Cold Springs.
Copper is more traditional. It’s been around forever, and some people just like the idea of metal pipes. It’s also a bit more resistant to UV exposure if you have any exterior runs. Copper typically lasts 50+ years and costs more upfront because the material and labor are both pricier.
If you’re budget-conscious or want the job done faster, go with PEX. If you’re planning to stay in the house forever and want the “premium” option, copper’s fine too. Honestly, both are massive upgrades over Kitec. We’ll walk you through the pros and cons based on your specific property, and you decide what makes sense.
It won’t increase your value the way a kitchen remodel might, but it removes a major red flag that can kill a sale or force you to drop your price. Buyers in El Dorado County know what Kitec is. Inspectors flag it. Lenders sometimes balk at financing homes with it.
If you’re selling a home in Cold Springs with Kitec still in place, you’re either replacing it before listing, negotiating a credit at closing, or watching buyers walk away. A documented Kitec repipe means you can sell without that hanging over the deal.
And from an insurance standpoint, it protects your investment. A lot of carriers won’t cover Kitec-related damage anymore, or they’ll non-renew your policy after a claim. A repipe keeps you insurable and keeps your home marketable. That’s worth more than the cost of the job.
You can, but it’s expensive and it doesn’t solve the problem. Kitec’s defect is universal—every fitting and every section of pipe is degrading at the same rate. When one fitting fails, the others aren’t far behind.
We’ve seen people spend $1,500 here, $2,000 there, chasing leaks for a couple of years. By the time they call us for a full repipe, they’ve already spent half the cost of the repipe on patches—and they still have Kitec in the walls.
Plus, every time a fitting lets go, you’re dealing with water damage. Drywall, flooring, maybe mold if it’s behind a wall and you don’t catch it right away. A full Kitec repipe in Cold Springs, CA stops that cycle. You pay once, it’s done right, and you’re finished thinking about it.
Local Resources
Other Services we provide in Cold Springs
