Hear from Our Customers
You already know the problem. Kitec plumbing doesn’t leak—it bursts. And when it does, you’re looking at thousands in water damage, insurance headaches, and a replacement job you should have done months ago.
The fittings corrode from the inside out. Dezincification creates blockages that increase pressure until something gives. Your insurance company knows this too, which is why they’re either charging you more or refusing to cover your home entirely.
Here’s what changes after a full Kitec replacement in Elmhurst, CA: your insurance premiums drop or coverage becomes available again. You stop checking walls for moisture. You stop wondering if today’s the day. And if you ever sell, buyers won’t walk away during inspection because of your plumbing.
We remove every inch of Kitec from your home and replace it with copper or PEX—systems that last decades, not years. The quote we give you is the price you pay. No diagnostic fees. No surprise charges when we open a wall.
Most replacements happen in one to three days depending on your home’s size and layout. You’ll have water access throughout most of the job, and we’ll walk you through exactly what to expect before we start.
We’ve been handling emergency plumbing in Elmhurst, CA for over 100 years. We’ve seen every type of pipe failure this area throws at homes—from the historic properties built in the early 1900s to the newer construction where Kitec was installed between 1995 and 2007.
Our crews know Elmhurst’s housing stock. We understand how your home was built, where your lines run, and what it takes to replace them without tearing apart more than necessary. Every plumber on our team is licensed and insured, and we carry professional-grade equipment on every truck.
We show up when we say we will. Our Google rating sits at 4.7 out of 5 based on 93 reviews, and customers consistently mention two things: we’re on time, and the final bill matches the estimate. That’s not marketing talk—it’s how we’ve stayed in business for a century.
If your Kitec system fails at 2 a.m., we answer. If you need a replacement scheduled around your work week, we make it happen. You’re not getting a call center or a runaround—you’re getting a local crew that’s been doing this work in Elmhurst longer than most companies have existed.
First, we schedule an inspection of your home to map out where your Kitec lines run. Most of it’s behind walls or under floors, so we use this step to give you an accurate quote based on the actual scope—not a guess. You’ll know the cost before we touch a tool.
Once you approve the quote, we schedule the replacement around your availability. On day one, we shut off water to the areas we’re working on and start removing Kitec pipe and fittings. We open only the walls and floors we need to access, and we do it carefully. This isn’t a demolition job—it’s surgical.
As we remove old pipe, we install new copper or PEX in its place. We test every connection for leaks before we close anything back up. Depending on your home’s size, this takes anywhere from one to three days. You’ll have limited water access during active work hours, but we restore service each evening when possible.
After the new system is installed and tested, we handle drywall patching and any necessary finish work to return your walls and floors to their original condition. Then we walk you through the completed job, show you where everything was replaced, and provide documentation for your insurance company.
The entire process is designed to get you back to normal as fast as possible while doing the job right the first time. No shortcuts. No temporary fixes. Just a complete replacement that eliminates your Kitec plumbing problems in Elmhurst, CA for good.
Ready to get started?
You’re getting complete removal of every Kitec pipe and fitting in your home. We don’t patch sections or try to work around problem areas—we take it all out. The replacement material is either copper or PEX depending on your home’s layout and your preference. Both last significantly longer than Kitec ever could.
Every connection is pressure-tested before we close walls. You’ll receive documentation of the work completed, which satisfies insurance requirements and provides proof of replacement if you sell your home. We also handle all necessary permits and inspections required in Elmhurst, CA.
The cost typically ranges from $4,500 for smaller homes to $15,000 for larger properties with complex layouts. That includes labor, materials, wall and floor repair, and cleanup. The quote we provide upfront is the number you’ll see on the final invoice.
Elmhurst’s housing stock ranges from century-old homes to modern builds, and Kitec primarily shows up in properties built or renovated between 1995 and 2007. If your home falls in that window, there’s a strong chance you have it. We’ve replaced Kitec systems in everything from compact single-story homes to multi-level properties with baselines running through crawl spaces and attics.
One thing to know about this area: California’s water quality varies, and some regions deal with harder water that accelerates Kitec deterioration. If you’ve noticed low water pressure, discolored water, or small leaks, your system is already failing. Waiting only increases the risk of a catastrophic burst and the damage that comes with it.
Check your water heater connections, under sinks, and anywhere pipes are visible in your basement or crawl space. Kitec pipe is usually blue for cold water and orange for hot water, though sometimes both are blue. The fittings are brass-colored and often stamped with “Kitec” or “KTC.”
If your home was built or renovated between 1995 and 2007, the chances are higher. That’s the window when Kitec was commonly installed before the recall in 2005. Even if you don’t see the pipes directly, you might spot them near your water heater or where supply lines enter your home.
If you’re not sure, we can inspect your system and confirm whether you have Kitec. There’s no charge for that assessment, and it takes about 20 minutes. Knowing for certain is worth it—especially if you’re dealing with insurance questions or planning to sell.
No, and here’s why: the fittings that connect Kitec pipes are no longer manufactured. That means even if we wanted to repair a section, we can’t source compatible parts. The sizing doesn’t match standard plumbing fittings either, so there’s no workaround.
Beyond that, Kitec fails because of a chemical process called dezincification. The brass fittings corrode from the inside as zinc breaks down when exposed to oxygen and moisture. Once that process starts in one area, it’s happening throughout your system. Fixing one leak doesn’t stop the others from developing.
Insurance companies understand this, which is why they won’t cover homes with Kitec long-term. They know it’s not a matter of if the system fails, but when. A full replacement is the only solution that actually solves the problem and gets your home insurable again.
If you’re only replacing the Kitec connections at your water heater, the cost is significantly lower than a whole-home replacement—usually between $800 and $1,500 depending on access and complexity. But here’s the issue: replacing just the water heater lines doesn’t address the Kitec running through the rest of your home.
Most of the time, if Kitec is at your water heater, it’s also in your walls feeding your sinks, showers, and appliances. Those lines are deteriorating at the same rate. Replacing one section buys you time, but it doesn’t eliminate the risk of a burst pipe somewhere else in your system.
For a full whole-home Kitec replacement in Elmhurst, CA, you’re looking at $4,500 to $15,000 depending on square footage and how your home is laid out. That includes removing all Kitec pipe and fittings, installing new copper or PEX, testing the system, and repairing any drywall or flooring we access. The quote we give you is the final price—no surprise additions.
Most insurance companies won’t cover the cost of replacing Kitec plumbing because it’s considered a maintenance issue, not sudden damage. However, if your Kitec system bursts and causes water damage, your policy may cover the damage to your home—but not the cost of replacing the failed plumbing itself.
That said, many insurers in California are now requiring Kitec replacement as a condition of coverage. If they discover you have Kitec during underwriting or a claim, they may increase your premiums significantly or refuse to renew your policy until it’s replaced. Some won’t insure homes with Kitec at all.
The good news: once you replace your Kitec system, your insurability improves and your premiums often drop. We provide full documentation of the replacement work, which you can submit to your insurance company as proof. That paperwork also helps if you sell your home, since buyers and their lenders will want confirmation that Kitec has been removed.
Most full replacements take one to three days depending on your home’s size and how accessible your plumbing is. A smaller single-story home with straightforward pipe runs can often be completed in a day. Larger homes or properties with multiple floors, finished basements, or complex layouts take closer to three days.
We work efficiently, but we don’t rush. Every connection gets tested for leaks before we close up walls or floors. We also coordinate the work to minimize disruption—you’ll have limited water access during active work hours, but we restore service each evening whenever possible so you’re not without water overnight.
Before we start, we’ll give you a clear timeline based on your specific property. We show up on time, work through the scope as planned, and communicate if anything changes. The goal is to get your home back to normal as quickly as possible while doing the job right the first time.
Call us immediately—we offer 24/7 emergency response for Kitec leak repair in Elmhurst, CA. A burst pipe can release hundreds of gallons of water in minutes, so speed matters. We’ll shut off your water, assess the damage, and start mitigation right away to minimize what gets destroyed.
Once the immediate crisis is handled, we’ll move into full replacement mode. At that point, you’re already dealing with the mess and expense of water damage, so replacing the entire system makes sense. Patching the burst section isn’t an option since the fittings are no longer made and the rest of your Kitec is just as vulnerable.
The better move is replacing your system before it bursts. You avoid the water damage, the insurance claim, the potential mold issues, and the stress of an emergency. We can schedule the work around your life instead of forcing it into the middle of a disaster. If you know you have Kitec, waiting only increases the risk.
Local Resources
Other Services we provide in Elmhurst
