Hear from Our Customers
You stop wondering when the next leak will hit. Kitec pipes fail without warning—one day everything’s fine, the next day you’re dealing with water damage, insurance claims, and a mess that could’ve been prevented.
When you replace Kitec pipes in Locke, CA before they burst, you eliminate the risk entirely. Your insurance company stops treating your home like a liability. Your property value stays protected because buyers won’t use failing pipes as a bargaining chip during negotiations.
Most importantly, you get certainty. No more worrying about coming home to a flooded house. No more paying higher premiums because your plumbing is a known risk. Just reliable copper or PEX piping that’s built to last decades, not years.
We’ve spent more than 24 years handling plumbing emergencies and full system replacements throughout El Dorado County and Sacramento County. We know what Kitec failure looks like because we’ve responded to the aftermath too many times.
Here’s what matters to you: we show up when we say we will, we quote the actual price upfront, and we don’t leave until the job’s done right. We’re licensed, insured, and we use high-quality Type L copper piping made in the USA—not whatever’s cheapest.
Locke homeowners need someone who understands the urgency of replacing Kitec plumbing before it becomes an emergency. That’s what we do, and we’ve been doing it long enough to know how to do it efficiently without cutting corners.
First, we assess your entire system using camera technology to see exactly what we’re dealing with. No guessing. We map out where every Kitec pipe runs so we know what needs to go and what stays.
Then we give you a complete quote. Not an estimate that changes later—the actual price. You’ll know what the full Kitec replacement costs before we start, and that’s what you’ll pay.
The replacement itself typically takes two to three days for an average home. We remove every piece of Kitec—pipes, fittings, everything—and replace it with copper or PEX piping. You can stay in your home during the work. We’re not tearing down walls unnecessarily; we’re routing new pipes efficiently and making sure everything’s sealed, tested, and ready to last.
Once it’s done, you have a plumbing system you can trust. We test for leaks, verify pressure, and make sure you’re set for the long term.
Ready to get started?
When we replace Kitec pipes in Locke, CA, we’re removing the entire system—not patching sections and hoping the rest holds up. Kitec fittings aren’t even manufactured anymore, so partial repairs don’t work. You need full replacement, and that’s what we do.
You get new copper or PEX piping throughout your home, installed to current code standards. We handle hot and cold water lines, making sure everything’s properly supported and insulated where needed. The work includes pressure testing to verify there are no weak points.
Homes built in the Sacramento area between 1995 and 2007 are the most likely to have Kitec. If your home falls in that range and you’re in Locke or nearby communities like Walnut Grove or Courtland, it’s worth having us take a look. The longer you wait, the higher the chance you’re dealing with a burst pipe instead of a planned replacement.
We also coordinate with your insurance company if needed. Many insurers in California have started flagging Kitec as a risk, which means higher premiums or coverage restrictions. Replacing it removes that problem entirely.
Full Kitec replacement typically runs between $5,000 and $15,000 depending on your home’s size, how accessible your plumbing is, and whether you’re replacing with copper or PEX. Larger homes with complex layouts cost more. Smaller homes with straightforward plumbing cost less.
Here’s the thing: that range is still cheaper than dealing with water damage from a burst pipe. Insurance claims for Kitec failures often don’t cover everything, and you’re left paying out of pocket for repairs, mold remediation, and replacing damaged belongings.
We give you an exact quote before we start. No diagnostic fees that turn into surprise charges later. You’ll know what you’re paying upfront, and that’s the number you’ll see on the final invoice.
No, and here’s why: Kitec fittings haven’t been manufactured since the recall started in 2005. Even if you patch one leak, the rest of your system is still failing. You’re just buying time until the next section bursts.
The brass fittings in Kitec systems corrode from the inside out. It’s not a matter of one bad pipe—it’s a system-wide defect. Plumbing experts across the industry agree that partial repairs don’t work because the problem is in the material itself, not just one isolated section.
Replacing Kitec plumbing entirely is the only solution that actually solves the problem. Anything else is temporary, and you’ll end up spending more on multiple repairs than you would’ve spent on one complete replacement.
Most homes take two to three days for complete Kitec pipe replacement. Smaller homes with simpler layouts might be done faster. Larger homes with multiple stories or complex plumbing runs might take an extra day.
You can stay in your home during the work. We’re not gutting your house—we’re accessing pipes through strategic points and rerouting new lines efficiently. There will be some disruption, but it’s manageable.
The timeline also depends on whether we’re replacing with copper or PEX. PEX installs faster because it’s more flexible and requires fewer fittings. Copper takes a bit longer but offers durability that some homeowners prefer. Either way, we work efficiently and we don’t drag the job out.
Yes, in a good way. Many insurance companies in California charge higher premiums for homes with Kitec or refuse to cover water damage related to Kitec failures. Some won’t insure homes with Kitec at all.
When you replace Kitec pipes, you remove that liability. Your insurer sees a home with updated plumbing that meets current standards, which often means lower premiums and full coverage for water damage. It also makes your home easier to sell because buyers won’t face the same insurance issues.
If you’re currently dealing with higher premiums or coverage restrictions because of Kitec, replacing it is one of the fastest ways to fix that problem. We can provide documentation of the replacement for your insurance company so they can update your policy accordingly.
Visible corrosion on brass fittings is the most obvious sign. If you see green or white buildup around connections, that’s corrosion eating through the fitting from the inside. Reduced water pressure is another indicator—it means buildup is restricting flow.
Small leaks around fittings are a warning that bigger failures are coming. Kitec doesn’t give you much notice. One day it’s a slow drip, the next day it’s a burst pipe flooding your home.
The problem is that most of the damage happens inside the fittings where you can’t see it. By the time you notice symptoms, the system is already compromised. That’s why replacing Kitec plumbing before you see obvious signs is the smarter move—you’re not waiting for failure to force your hand.
We respond fast, we quote the real price upfront, and we’ve been doing this for over 24 years. You’re not getting a rookie crew figuring things out on your dime—you’re getting licensed professionals who’ve handled hundreds of repiping jobs.
We use quality materials, not the cheapest option we can find. Type L copper piping made in the USA, installed to code, tested for leaks before we leave. If we’re using PEX, it’s the same standard—quality materials installed correctly.
What sets us apart is transparency. The price we quote is the price you pay. No surprise charges, no diagnostic fees that balloon into something else. We show up when we say we will, we do the work right, and we don’t leave until you have a plumbing system that works. That’s it.
Local Resources
Other Services we provide in Locke
