Hear from Our Customers
High water pressure doesn’t just waste water—it destroys your plumbing from the inside out. Every day your pipes handle excessive pressure, they’re getting weaker. Faucets start dripping constantly. Toilet valves fail. Appliances burn out early. Your water bills climb because everything uses more water than it should.
A properly installed water pressure regulator changes all that. Your fixtures last longer. Your appliances run efficiently. Your water bills drop. Most importantly, you stop worrying about surprise leaks that could flood your home.
In Hood, where city water pressure often exceeds safe levels for residential use, a pressure regulator isn’t just smart—it’s essential protection for your biggest investment.
We’ve been the go-to plumbing contractor for Hood and surrounding communities since day one. We’re not the biggest company around, and we like it that way. Small means we can keep our overhead low and our prices fair. It means when you call, you get someone who knows your area and understands the specific challenges Hood homeowners face.
Our team knows California’s plumbing code requirements inside and out. We’ve installed hundreds of pressure regulators throughout El Dorado County, and we’ve seen what happens when homeowners wait too long to address high water pressure issues. That’s why we offer free estimates—because catching problems early saves everyone money.
We’re licensed, insured, and committed to doing the job right the first time. No surprises, no upselling, just honest work at fair prices.
First, we test your current water pressure to see exactly what we’re dealing with. Most Hood homes get water pressure between 80-150 PSI from the city, but your home’s plumbing works best around 55-65 PSI. We’ll show you the readings so you can see the difference.
Next, we locate the best spot for your pressure regulator—usually right after your main water shut-off valve. We shut off your water supply, install the regulator, and make sure all connections are secure and leak-free. The whole process typically takes 2-3 hours.
Finally, we test everything to make sure your pressure is exactly where it should be. We’ll adjust the regulator if needed and walk you through how it works. Before we leave, we clean up completely and make sure you’re satisfied with the work.
Ready to get started?
Every water pressure regulator installation includes pressure testing before and after the work, so you know exactly what changed. We use quality brass regulators that last longer than cheaper alternatives, and we back our work with a solid warranty.
Hood’s location in the Sierra Nevada foothills means elevation changes can create significant pressure variations throughout the area. We account for these local conditions when selecting and adjusting your regulator. What works in Sacramento might not be right for your specific location.
We also inspect your existing plumbing while we’re there. High water pressure often causes damage you can’t see yet—like stress fractures in pipes or worn valve seals. Catching these issues early prevents bigger problems later. If we spot anything concerning, we’ll let you know, but we never push unnecessary repairs.
If your water pressure feels too strong in showers, faucets drip constantly, or you hear banging in your pipes, you likely have high water pressure. The only way to know for sure is to test it with a pressure gauge.
Most Hood homes connected to city water have pressure above the recommended 80 PSI limit. California plumbing code actually requires pressure regulators when incoming pressure exceeds this level. We can test your pressure for free during an estimate—it takes about five minutes and gives you the exact PSI reading.
You might also notice higher water bills if your pressure is too high. Toilets run longer, faucets use more water, and appliances work harder than they should. A pressure regulator typically pays for itself within a year through lower water bills alone.
Most pressure regulator problems require replacement rather than repair. These devices have internal springs and diaphragms that wear out over time—usually after 8-12 years of use. When they fail, the whole unit needs to be swapped out.
Sometimes we can adjust a regulator that’s working but set incorrectly. This is common in homes where someone tried to fix pressure issues by turning the adjustment screw without understanding how it works. Adjustment is quick and inexpensive compared to full replacement.
If your regulator is leaking, making noise, or not controlling pressure consistently, replacement is almost always the right solution. Trying to patch up an old regulator usually just delays the inevitable and can lead to water damage if it fails completely.
Most installations take 2-3 hours from start to finish. This includes testing your current pressure, shutting off water, installing the new regulator, testing again, and adjusting if needed. Simple replacements where we’re swapping out an existing regulator can be faster.
The timeline can stretch if we run into complications like corroded pipes or hard-to-reach locations. Older homes sometimes need additional plumbing work to accommodate a modern regulator properly. We’ll let you know upfront if we spot anything that might add time to the job.
We always plan installations so your water is only off for the minimum time necessary. Most of the work happens with your water still on—we only shut it off for the actual installation and testing phases.
A properly installed and adjusted pressure regulator should give you ideal water pressure, not weak pressure. We set most residential regulators between 55-65 PSI, which provides strong, consistent flow without the problems that come with excessive pressure.
Many Hood homeowners are surprised to find that their water pressure actually feels better after regulator installation. Instead of pressure that varies throughout the day or feels harsh and sputtering, you get steady, comfortable flow from every fixture.
If you’re used to very high pressure, there might be a brief adjustment period. But most customers tell us their showers feel better, their faucets work more smoothly, and they don’t miss the excessive pressure at all. We can always adjust the regulator if you want slightly higher or lower pressure after living with it for a while.
When a pressure regulator fails, it usually fails open, meaning your home suddenly gets full city water pressure again. This can cause immediate damage—burst pipes, blown faucet seals, or appliance failures. The longer it stays broken, the more damage accumulates.
Some regulators fail closed, which cuts off water flow to your home entirely. This is less damaging but obviously inconvenient. Either way, a failed regulator needs immediate attention to prevent bigger problems.
This is why we recommend annual pressure checks, especially for regulators over 8 years old. Catching a failing regulator before it completely breaks saves you from emergency repairs and potential water damage. Most failures give warning signs like fluctuating pressure or unusual noises before they quit entirely.
Water pressure regulator installation in Hood typically runs $300-650, depending on the type of regulator you need and the complexity of the installation. This includes the regulator itself, all necessary fittings, and professional installation with testing.
Basic residential regulators cost less than commercial-grade units or models with special features. If your existing plumbing needs modifications to accommodate the regulator, that can add to the total cost. We provide upfront pricing so you know exactly what you’re paying before we start work.
Most homeowners find that a pressure regulator pays for itself within a year through reduced water bills and fewer plumbing repairs. When you factor in the protection it provides against expensive damage from high water pressure, it’s one of the smartest investments you can make in your home’s plumbing system.
Local Resources
Other Services we provide in Hood
